井下带式输送机撒煤清理机器人液压系统设计

Design of hydraulic system for underground belt conveyor coal spillage cleaning robot

  • 摘要: 带式输送机运输过程中因装载过量或胶带跑偏等原因会发生物料撒落与堆积,而现有清理机器人无法有效清理带式输送机下方及内侧的撒煤,同时,其液压系统未适配撒煤清理场景所具有的间歇性和多清扫机构交替作业的工况特点。针对上述问题,设计了一种井下带式输送机撒煤清理机器人液压系统。该液压系统由负载敏感泵系统和侧向扒料、回转挖运、履带底盘3个独立运行的液压子系统组成;使用开式负载敏感泵作为动力源,实现压力自适应匹配与流量按需供给;在各液压子系统中集成中位机能换向阀与双补油单向阀组,抑制扒煤板高频往复伸缩过程中的换向冲击与吸空现象。利用AMESim对液压系统动态特性进行了仿真分析,结果表明:负载敏感泵在负载变化区间内能够快速跟踪负载并保持稳定压差输出,验证了液压系统压力对负载变化的跟随能力;侧向扒料液压系统的伸缩液压缸换向流量能在0.15 s内完成方向切换且换向冲击持续时间短,回转挖运液压系统的回转液压马达在稳定回转状态下流量波动较小,说明中位机能换向阀与双补油单向阀组能够有效抑制换向冲击。撒煤清理作业试验结果表明,机器人侧向扒料机构单次有效清理面积达0.8 m2,撒煤清理效率达0.6 t/h,所设计的液压系统能有效支撑机器人完成“扒出—聚拢—挖取—回转—卸料”的撒煤清理作业流程。

     

    Abstract: Material spillage and accumulation can occur during belt conveyor transport owing to overloading or belt misalignment. Existing cleaning robots cannot effectively remove spilled coal from beneath and along the inner sides of belt conveyors, and their hydraulic systems are not adapted to the intermittent operation and alternating use of multiple cleaning mechanisms required in coal spillage cleaning. To address these problems, a hydraulic system design for an underground belt conveyor coal spillage cleaning robot was proposed. The hydraulic system comprised a load-sensing pump system and three independently operated hydraulic subsystems for lateral raking, slewing excavation and transfer, and the crawler chassis. An open-circuit load-sensing pump was used as the power source to provide adaptive pressure matching and flow on demand. Directional control valves with center-position flow configurations and dual make-up check valve assemblies were integrated into each hydraulic subsystem to suppress pressure shocks during direction reversal and prevent cavitation during high-frequency reciprocating extension and retraction of the coal raking plates. The dynamic characteristics of the hydraulic system were simulated using AMESim. The results showed that the load-sensing pump rapidly tracked load changes and maintained a stable pressure differential throughout the load variation range, verifying the ability of the hydraulic system pressure to follow load changes. Flow in the telescopic hydraulic cylinder of the lateral raking subsystem reversed direction within 0.15 s, and the reversal shock was short-lived. The slewing hydraulic motor in the slewing excavation and transfer subsystem exhibited small flow fluctuations during steady rotation. These results indicated that the directional control valves with center-position flow configurations and dual make-up check valve assemblies effectively suppressed reversal shocks. Coal spillage cleaning tests showed that the lateral raking mechanism achieved an effective cleaning area of 0.8 m2 per operation, and the robot achieved a coal spillage cleaning rate of 0.6 t/h. The designed hydraulic system can effectively support the complete coal spillage cleaning sequence of raking out, gathering, excavating, slewing, and unloading.

     

/

返回文章
返回